Water Heater Safety Warnings

Posted by on Dec 3, 2013 in Water Heater Repair Yonkers

Properly preserving ones water heater is vital not so it works to its complete potential and can conserve some energy cash, however for safety issues too. Yes, it can blow up – it does not occur too often for homeowners, however certainly this is something that Water Heater Repair Yonkers¬†doesn’t desire to have occur to you!

Venting can be kind of technical however we will review the basics right here. The vent ought to be the exact same diameter as the draft diverter of the water heater tank. It is supposed to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent ought to go out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some flexibility in the direction they are vented.

Any roof or wall that the vent goes through need to be a double wall. The single wall pass throughs should be screwed with 3 screws per area. If these fundamentals are not adhered to, the vents can fall apart with time and carbon monoxide can cause major problems within ones home. Naturally we don’t desire that to happen!

The only other issue with venting is that of backdrafting. The fumes can eat the vents with acid condensation. If plenty of this gets on cold piping and the water heater it will not be a good scenario for a correctly working water heater. If the fumes return inside the instead of being correctly vented outside, the fumes can get in the living areas of the house. Soot problems can arise as well.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When 2 these 2 metals are assembled in water electrolysis happens. The process wears away one metal away to safeguard the other. This process is essential in safeguarding the inside of the water heater. Examination for leakages must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a vital part of the water heater, for it assists to make sure the darn thing does not explode under pressure if the temperature goes beyond the right limitations the water heater is designed for. Once a year (at least) the T&P valve must be examined to see to it, it is working appropriately, for they can be vulnerable to failure. Merely lifting up on the handle water must stream easily out and stop when the handle is released. If it simply runs or trickles, or does nothing at all, it will have to be changed.

The drain lines for the T&P line must not be routed up, because water doesn’t flow uphill too well. See to it it goes downhill and or out please. If water is running out the drain line regularly, it is the sign of something incorrect too. It could be one of several different things that we will not enter into here – simply speak to a local plumber please.

Earthquake Straps
Yep, even if you do not live in an earthquake area and are required to have these on ones water heater, it is a pretty good idea to do so. It looks like most all new houses in sub-divisions nowadays have the water heater in the garage. Yes, there is usually a concrete curb in front of it so one does not drive a car into it, however things can unintentionally knock it over so be safe and strap that thank in.

Temperature Level Setting
It seems most residential water heater tanks have settings of warm – hot – really hot … and not degree settings. Some “suggestions” on saving energy in the house particularly in the winter season time, state to decrease the setting on the tank to 120 degrees. That’s great for conserving energy but legionella germs, which causes Legionnaire’s illness can grow at 120 degrees. By breathing in the mist from the water in the shower, one can breathe in the microorganisms. Search for a medium in between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These normally are made from aluminum and there is absolutely nothing wrong with that in theory, though we suggest utilizing magnesium ones. Let’s say for whatever reason there is some kind of emergency or catastrophe where one lives and one needed to use the water in the water heater for drinking water (because bunches of emergency readiness people advise doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be laden with aluminum substances, which is bad for the human body. It is bad for the stomach, intestinal tract and joints.

The anodes assist with rust security and are vital in extending the life of the water heater. They can also assist with odor troubles with the water. Overall, magnesium anodes just work better for a great deal of different reasons like the wellness benefits, let develop of sediment, a quieter water heater, and they often work more competent with softened water.

Drain Valve
Ok, simply examine it a minimum of yearly to make certain the darn thing opens and works. And it is good to drain and flush the tank a minimum of once a year anyhow (something you obviously are doing already). If for some reason one has to make use of the water throughout a catastrophe or drain it to rather a loud tank and have not drained it regularly, and it doesn’t open, it will take longer to remedy the trouble you are at first attempting to deal with.

Combustion Changer Hatch
Given that gas and oil water heaters breathe the air sucked in from underneath, combust with it and exhale it, it is necessary to keep the location around it, specifically below the water heater, clean and swept. If if is not burning appropriately, it can cause composing issues (mentioned above), along with combustion and fume issues and potentially be a fire hazard. Some of examining the chamber and exactly how the flame burns is objective so we are not going to enter into a bunch of information here. it is important to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not a good indicator at all. One must see some blue flame at the bottom when it burns and orange and yellow at the top, nonetheless, the yellow need to not be extremely high up. One need to see grey metal, some white condensation marks are ok.

Water Heater Repair Yonkers has put together an infographic to highlight the information above:

Water Heater Repair Yonkers

Enhanced by Zemanta